This adds a `nomad alloc stop` command that can be used to stop and
force migrate an allocation to a different node.
This is built on top of the AllocUpdateDesiredTransitionRequest and
explicitly limits the scope of access to that transition to expose it
under the alloc-lifecycle ACL.
The API returns the follow up eval that can be used as part of
monitoring in the CLI or parsed and used in an external tool.
Noticed that `detected drivers` log line was misleading - when a driver
doesn't fingerprint before timeout, their health status is empty string
`""` which we would mark as detected.
Now, we log all drivers along with their state to ease driver
fingerprint debugging.
I noticed that `watchNodeUpdates()` almost immediately after
`registerAndHeartbeat()` calls `retryRegisterNode()`, well after 5
seconds.
This call is unnecessary and made debugging a bit harder. So here, we
ensure that we only re-register node for new node events, not for
initial registration.
Here we retain 0.8.7 behavior of waiting for driver fingerprints before
registering a node, with some timeout. This is needed for system jobs,
as system job scheduling for node occur at node registration, and the
race might mean that a system job may not get placed on the node because
of missing drivers.
The timeout isn't strictly necessary, but raising it to 1 minute as it's
closer to indefinitely blocked than 1 second. We need to keep the value
high enough to capture as much drivers/devices, but low enough that
doesn't risk blocking too long due to misbehaving plugin.
Fixes https://github.com/hashicorp/nomad/issues/5579
In Nomad 0.9, we made volume driver handling the same for `""`, and
`"local"` volumes. Prior to Nomad 0.9 however these had slightly different
behaviour for relative paths and named volumes.
Prior to 0.9 the empty string would expand relative paths within the task
dir, and `"local"` volumes that are not absolute paths would be treated
as docker named volumes.
This commit reverts to the previous behaviour as follows:
| Nomad Version | Driver | Volume Spec | Behaviour |
|-------------------------------------------------------------------------
| all | "" | testing:/testing | allocdir/testing |
| 0.8.7 | "local" | testing:/testing | "testing" as named volume |
| 0.9.0 | "local" | testing:/testing | allocdir/testing |
| 0.9.1 | "local" | testing:/testing | "testing" as named volume |
Currently, when logmon fails to reattach, we will retry reattachment to
the same pid until the task restart specification is exhausted.
Because we cannot clear hook state during error conditions, it is not
possible for us to signal to a future restart that it _shouldn't_
attempt to reattach to the plugin.
Here we revert to explicitly detecting reattachment seperately from a
launch of a new logmon, so we can recover from scenarios where a logmon
plugin has failed.
This is a net improvement over the current hard failure situation, as it
means in the most common case (the pid has gone away), we can recover.
Other reattachment failure modes where the plugin may still be running
could potentially cause a duplicate process, or a subsequent failure to launch
a new plugin.
If there was a duplicate process, it could potentially cause duplicate
logging. This is better than a production workload outage.
If there was a subsequent failure to launch a new plugin, it would fail
in the same (retry until restarts are exhausted) as the current failure
mode.
Fixes#5566 .
Fix a case where docker logging process may lock up nomad agent restart.
Looks like we have a case where docker logger is started even through logmon isn't. In such case, the fifo writer blocks indefinitely and because the open operation happens in the main goroutine, nomad agent blocks indefinitely.
This fixes the issue where the fifo open operation happens in goroutine instead of main goroutine.
We should follow up independently to ensure logmon <-> dockerlogger ordering and consider having task recovery happen in non-main goroutine with some sensible timeouts.
Renewal time was being calculated as 10s+Intn(lease-10s), so the renewal
time could be very rapid or within 1s of the deadline: [10s, lease)
This commit fixes the renewal time by calculating it as:
(lease/2) +/- 10s
For a lease of 60s this means the renewal will occur in [20s, 40s).
